Starting generation of Calibration File 
FS version = 0009.0010.0004 
time_zero = 9738000 
Found #2847 errors of type = ERROR ch -317 Total power integrator overflow on IF2 
Found #362 errors of type = ERROR qk -211 Tsys value for device va overflowed or was less than zero. 
Found #359 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #332 errors of type = ERROR ch -308 ve total power integrator overflow 
Found #206 errors of type = ERROR ch -308 v9 total power integrator overflow 
Found #144 errors of type = ERROR qk -211 Tsys value for device ve overflowed or was less than zero. 
Found #116 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #57 errors of type = ERROR ch -308 va total power integrator overflow 
Found #32 errors of type = ERROR qk -211 Tsys value for device vb overflowed or was less than zero. 
Found #22 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #8 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #5 errors of type = ERROR qk -211 Tsys value for device vd overflowed or was less than zero. 
Found #4 errors of type = ERROR ch -308 vb total power integrator overflow 
Found #3 errors of type = ERROR st  -36 The antenna is not in operating mode. 
Found #2 errors of type = ERROR st -115 [ANTCN] - WARNING: X S paths are not in line. 
Found #2 errors of type = ERROR qk -211 Tsys value for device v6 overflowed or was less than zero. 
Found #1 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #1 errors of type = ERROR qk -211 Tsys value for device v2 overflowed or was less than zero. 
Found #1 errors of type = ERROR st -105 [ANCOM] - Too many errors from LU      . 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these  parameters:   
RX1 min= 100000 max= -1
RX2 min= 100000 max= -1
RX3 min= 100000 max= -1
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r4427ma.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max 114.7 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 76.8 ymax 271.3 
in match_chan ft1= r4427ma.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 114.7 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 110.6 ymax 236.5 
in match_chan ft1= r4427ma.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 114.7 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 9.5 ymax 305