Starting generation of Calibration File 
FS version = 0009.0010.0004 
time_zero = 8960400 
Found #16 errors of type = ERROR st   -2 Antenna timed out. 
Found #4 errors of type = ERROR st   -4 Interface not set to remote. 
Found #3 errors of type = ERROR st   -7 Antenna off-source! 
Found #2 errors of type = ERROR ch   -4 Device if timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device v6 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device v8 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device v1 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device v2 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch -309 v5 alarm is on 
Found #2 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #2 errors of type = ERROR an   -7 Antenna communications restored. 
Found #2 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #2 errors of type = ERROR ch   -4 Device vb timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device v4 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device v7 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device v3 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device vf timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device ve timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device va timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device v5 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device vd timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device i3 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch   -4 Device vc timed-out on response from MATCN 
Found #2 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #2 errors of type = ERROR ch   -4 Device v9 timed-out on response from MATCN 
Found #1 errors of type = ERROR ch -313 IF2 attenuator does not check with requested value 
Found #1 errors of type = ERROR ch -362 IF3 attenuator does not check with requested value. 
Found #1 errors of type = ERROR qs -305 No parameters are allowed after: stow  idle  disable  or service. 
Found #1 errors of type = ERROR m5 -900 Check formatter serial number even 
Found #1 errors of type = ERROR ch -312 IF1 attenuator does not check with requested value 
Found #1 errors of type = ERROR st   -6 Antenna control restored. 
Found #1 errors of type = ERROR m5 -906 MARK5 return code 6: inconsistent or conflicting request 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these SK parameters: 00(BXFNT) 02(LO_TMP) 03(DCAL_T)
RX1 min= 21.80 max= 2010.103.17:30:11.14
RX2 min= 47.60 max= 47.90
RX3 min= 34.60 max= 35.80
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= t2068ny.log.tsy1.ntup nt1= 7 st1= 1u tt= 1
set scale tsys1 [2] min max 53.7 78.6
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin -5 ymax 70.8 
in match_chan ft1= t2068ny.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 53.7 78.6
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 46.1 ymax 81.7 
in match_chan ft1= t2068ny.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 53.7 78.6
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 60.1 ymax 116.8