==================================== crds96 ==================================== Hh : About 30% late (10 sec) on source. Ho : Most of scans late 19 seconds. Ke : Warning! Continous cal not enable for DBBC (18:00-23:25). Reset DBBC at 00:08. Ww : Late start (18:00-20:30). No problems found for : Yg ================================ crds96hh READY ================================ 2018-06-20 14:56:39 crds96, HartRAO, Ready-message Session crds96 ready message for HartRAO. ----------------------------------------- Comments: HartRAO is ready to start the experiment First source: 1829-207 at 18:09:46 UT FMOUT-GPS: 5.7527 microseconds Wx: Temperature (C): 20.4 Pressure (mBar): 869 Humidity (%): 22.9 Sky Conditions: clear skies Cable difference is: longer cable makes the reading smaller by 1086.5 microseconds and is nominal Pointing values: na Tsys (x1/s/x2): 47.4/71.5/51.6 ================================ crds96hh START ================================ 2018-06-20 18:09:46 crds96, HartRAO, Autostart-message Session crds96 auto-start message for HartRAO. ---------------------------------------------- Started recording with source: 1829-207 at 171.18:09:46 UT ================================ crds96hh STOP ================================= 2018-06-21 17:45:22 crds96, HartRAO, Stop-message Session crds96 stop message for HartRAO. ---------------------------------------- Comments: HartRAO has completed CRDS96 Weather conditions: clear skies throughout Data will be e-shipped to Washington Disk Inventory: A 0, B 0, C 0, D 0, E 0, F 0, G 3, H 0, (other larger) 3 Observation finished at: 17:44:25 UT ================================ crds96ho WIKI ================================= 2018-06-21 16:18:00 crds96 Hobart 26m Disk VSN: HOB+0119/32000 | data volume at the begining 19828.475 GB . 1800UT- Experiment started OK (mas) When experiment started, received “ WARNING: error qo -301 warning: onsource status is slewing!” for each scan. All clocks at FMSET are synchronise. 23:30UT - Autocorrelation spectra not updating. Lucas fixed based on similar error where procedure file didn't include checkmk5 command (Ross). 13:45UT - 70K stage at ~90K and climbing, pressure at 3.6 microns mercury. Heading out to Mt Pleasant to fix. (Patrick) ================================ crds96ke WIKI ================================= 2018-06-21 16:18:00 crds96 Katherine 12m Disk VSN: HOB +0088/8000 | data volume at the begining 1.795 GB . 1800UT- Experiment started OK (mas) When experiment started, received “Warning: error tc -301 continuous cal not enabled for dbbc” for each scan 23:21UT - After discussion with Warren decided to reboot dbbc to see if that fixed continuous cal error. Halted after scan no0385, first good scan no0388 (Ross). 00:08UT - Noticed difference in procedure file between crds96 and previous crds experiments and corrected this error; missed scan no0394. Error still present, leaving for Warren to look at later (Ross). 13:29UT - Fixed continuous cal not enabled error by changing cont_cal=off to cont_cal=on in the setup01 function of the procedure file, based off the previous crds95 procedure file. (Patrick) ================================ crds96yg WIKI ================================= 2018-06-21 16:18:00 crds96 Yarragadee 12m Disk 1 VSN: GSFC+022/8000 | data volume at the begining 1.923 GB . Recorded 7469.724 GB on this disk. Disk 2 VSN: BKG-0065 | data volume at the begining 0.0 GB . 1800UT- Experiment started OK (mas) 16:09UT - Manually drudged summary files. Noticed that data for Yg & Ho is 8064GB, while module in mk5 is 8000GB. Called up Yg and swapped modules inbetween scans. Resumed schedule with scan No0551 at 16:11:58 (1:48 into scan). (Patrick) ================================================================================