RV138 (Astrometric/Geodetic VLBA-138) 2019 NOV 25 17:00 UTC DOY 329 Notes prepared by David Gordon NVI/GSFC Special notes for this session: =============================== This session will use the RDBE/DDC/Mark5C system at the VLBA sites, as in previous RV sessions. The X-band frequencies are: 8365.75, 8445.75, 8805.75 and 8925.75 MHz, and spans 560 MHz. The S-band frequencies are: 2232.75, 2262.75, 2372.75 and 2392.75 MHz, and spans 160 MHz. The ending in .75 MHz is necessary at the VLBA stations. Therefore it will not be possible to monitor phase cals using the 10 kHz filters. NOTE: WE ARE INCREASING THE CHANNEL BANDWIDTHS FROM 8 TO 16 MHZ. RV138 will record 8 16-MHz bandwidth channels using 2-bit sampling. The bit rate will be 512 Mbits/sec. The data will be correlated at the VLBA using the VLBA DiFX software correlator. There are 4 non-VLBA stations scheduled - HARTRAO, NYALES20, ONSALA60 and WETTZELL. These stations should see the "Special operations notes for non-VLBA stations" section below for special instructions. To facilitate fringe-finding, there are some long scans on fairly strong sources with most antennas at the beginning and near the end of the schedule. All stations please try to be onsource and recording data for these scans. These scans are: Source Start DURATIONS name yyddd-hhmmss Br Fd Hh Hn Kp La Mk Nl Ny On Ov Pt Sc Wz 1803+784 19329-170000| 366 394 372 396 394 480 385 300 383 480 395 384 369| 1929+226 19329-170738| 356 338 300 337 337 347 345 443 436 343 300 443| 1929+226 19330-163820| 300 303 344 300 301 300 300 336 327 300 323 344| 1726+455 19330-164445| 300 312 300 311 309 321 307 301 300 306 310 304 321| We are again using the 'Fill' scheduling option. 'Fill' is run after a schedule is finished in the normal manner. It increases the scan times at stations, when possible, based on how much idle time each station has before its next scan. We used a 'FILL_OFF' margin of 5 seconds. Using 'Fill' on the original schedule, the average observing time increases from 48% to 61%, and the average idle time decreases from 23% to 10%. The observing time increases most at the faster antennas and least at the slower antennas. Purpose ======= This is the sixth of six coordinated astrometric/geodetic sessions in 2019 that use the full 10-station VLBA plus several geodetic stations capable of recording VLBA modes. This year's series is a continuation of the highly successful RDV series begun in 1997. These are now being run under the USNO's VLBA time allocation. The RV sessions are now being run on Mondays, concurrently with an R1 session for comparison purposes. These sessions are being coordinated by the geodetic/astrometric VLBI programs of USNO, NASA and NRAO. They have been designed so that the same data set may be used by each agency for its particular goals. USNO, NASA and Bordeaux Observatory will perform imaging and study possible corrections for source structure. These sources will establish a set of core reference sources with known structure and precisely known positions. These data will help provide the basis for evaluating the long term stability of the radio reference frame and the ultimate accuracy of wide angle astrometric measurements of extragalactic radio sources using VLBI. NASA and USNO will analyze this data to determine and maintain high accuracy terrestrial reference and celestial reference frames. The data will incorporate the VLBA stations into the VLBI reference frame through the inclusion of other geodetic stations for which we have long histories. This data will also produce highly accurate Earth orientation results and possibly the best nutation results ever produced. NASA and NRAO will use these sessions to provide a service to users who request high quality positions for a small number of sources. While the quality of these results will be high, the observing and data reduction overhead required will be minimal because a small number of such sources can be incorporated into a session of the regular geodetic observations, instead of requiring special observations. For each RV session we will select a set of ~60 sources from the pool of geodetic and monitoring sources. A number of poorly observed and/or new requested sources will also be included to obtain or improve their positions. Schedule information ==================== This is a new schedule generated by David Gordon at GSFC using sked. Schedule file name: rv138.skd At the IVS Data Center (ftp://cddisa.gsfc.nasa.gov/vlbi/ivsdata/aux/2019/rv138): Sked file: rv138.skd Text file: rv138.txt At the VLBA/NRAO: VLBA Pointing files: rv138crd.br rv138crd.fd rv138crd.hn rv138crd.kp rv138crd.la rv138crd.mk rv138crd.nl rv138crd.ov rv138crd.pt rv138crd.sc Summary file: rv138.sksum Sked file: rv138.skd Text file: rv138.txt Vex file: rv138.vex This session uses the VLBA stations and 4 IVS stations. The IVS stations are: HARTRAO, NYALES20, ONSALA60 and WETTZELL. Below is the sked summary. Key: Br=BR-VLBA Fd=FD-VLBA Hh=HARTRAO Hn=HN-VLBA Kp=KP-VLBA La=LA-VLBA Mk=MK-VLBA Nl=NL-VLBA Ny=NYALES20 On=ONSALA60 Ov=OV-VLBA Pt=PIETOWN Sc=SC-VLBA Wz=WETTZELL Br Fd Hh Hn Kp La Mk Nl Ny On Ov Pt Sc Wz Avg % obs. time: 58 60 57 62 59 60 51 60 65 71 59 60 61 70 61 % cal. time: 6 6 3 5 6 6 5 6 4 3 6 6 5 4 5 % slew time: 27 27 33 24 27 26 21 26 16 13 26 27 25 8 24 % idle time: 8 6 6 8 6 7 22 8 15 12 8 6 8 17 10 total # scans: 497 522 224 444 540 527 416 481 342 265 517 536 433 323 433 # scans/hour : 21 22 9 19 23 22 17 20 14 11 22 22 18 13 18 Avg scan (sec): 101 99 220 120 94 98 106 108 163 232 98 97 122 188 131 # data tracks: 16 16 16 16 16 16 16 16 16 16 16 16 16 16 # Mk5 tracks: 16 16 16 16 16 16 16 16 16 16 16 16 16 16 Total TB(M5): 1.61 1.66 1.58 1.71 1.63 1.65 1.42 1.67 1.79 1.96 1.62 1.66 1.69 1.95 1.69 # OF OBSERVATIONS BY BASELINE | Br Fd Hh Hn Kp La Mk Nl Ny On Ov Pt Sc Wz Total -------------------------------------------------------------------------------- Br| 371 15 265 386 391 350 337 153 46 421 388 243 61 3427 Fd| 32 302 496 495 311 390 104 44 419 503 293 60 3820 Hh| 73 22 29 0 45 135 197 9 29 81 200 867 Hn| 281 303 168 372 155 88 236 297 372 132 3044 Kp| 494 343 368 103 35 460 513 276 48 3825 La| 309 399 110 45 428 517 293 59 3872 Mk| 232 101 17 386 319 167 29 2732 Nl| 131 61 319 391 342 87 3474 Ny| 179 116 112 120 205 1724 On| 26 44 80 223 1085 Ov| 440 234 42 3536 Pt| 293 57 3903 Sc| 134 2928 Wz| 1337 Number of 2-station scans: 0 Number of 3-station scans: 236 Number of 4-station scans: 159 Number of 5-station scans: 61 Number of 6-station scans: 85 Number of 7-station scans: 102 Number of 8-station scans: 64 Number of 9-station scans: 72 Number of 10-station scans: 135 Number of 11-station scans: 33 Number of 12-station scans: 17 Number of 13-station scans: 9 Number of 14-station scans: 0 Total number of scans: 973 Total number of obs: 19787 INTENSIVE BREAKS ================ There will be an IVS INT01 Intensive session scheduled during RV138. Wettzell will drop out from 18:15 - 19:45 on DOY 329 for this Intensive. SOURCE SELECTION ================ There are a total of 79 sources in this session, 60 from the geodetic source list and 19 are sources with few or no previous observions in IVS sessions. SCHEDULING ALGORITHMS ===================== This schedule uses the "SRCEVN SQRT" mode of Sked. In the absence of any constraints, Sked will preferentially observe strong sources that have high visibility. This mode attempts to smooth out the number of observations per source. RECORDING MODE and FREQUENCIES ============================== The data will be recorded using the following setup: 8 channels 1:2 fan-out 32 MHz sample rate 2-bit sampling This recording mode is a modified version of 256-8(RDV). There is no correlator speed-up factor. The frequency sequence covers 560 MHz at X-band and 160 MHz at S-band using 4 channels in each band. At the VLBA, the X-band uses two LO's in order to fit into the VLBA 512 MHz passband. At the Mark4 stations, the X-band uses both the high and low parts of the geodetic receivers. Because only 8 channels are available when observing with the VLBA/RDBE/DDC systems, a wider spanned bandwidth is not advisable. The following tables list the setup for the VLBA stations and the geodetic stations with DBBC, Mark IV, Mark 5, and VLBA5 back ends. VLBA | HARTRAO Chan Sky Tracks LO IF BBC | LO IF BBC BBC# 1 X 8365.75 2, 4, 6, 8 7600 B 765.75| 8080.0 A1 285.75 3 2 X 8445.75 10,12,14,16 7600 B 845.75| 8080.0 A1 365.75 4 3 X 8805.75 18,20,22,24 9600 D 794.25| 8080.0 B2 725.75 5 4 X 8925.75 26,28,30,32 9600 D 674.25| 8080.0 B2 845.75 6 5 S 2232.75 3, 5, 7, 9 3100 A 867.25| 2020.0 C1 212.75 9 6 S 2262.75 11,13,15,17 3100 A 837.25| 2020.0 C1 242.75 10 7 S 2372.75 19,21,23,25 3100 A 727.25| 2020.0 C1 352.75 13 8 S 2392.75 27,29,31,33 3100 A 707.25| 2020.0 C1 372.75 14 VLBA | NYALES20 Chan Sky Tracks LO IF BBC | LO IF BBC BBC# 1 X 8365.75 2, 4, 6, 8 7600 B 765.75| 8080.0 1N 285.75 3 2 X 8445.75 10,12,14,16 7600 B 845.75| 8080.0 1N 365.75 4 3 X 8805.75 18,20,22,24 9600 D 794.25| 8580.1 3N 225.65 5 4 X 8925.75 26,28,30,32 9600 D 674.25| 8580.1 3N 345.65 6 5 S 2232.75 3, 5, 7, 9 3100 A 867.25| 2020.0 2N 212.75 9 6 S 2262.75 11,13,15,17 3100 A 837.25| 2020.0 2N 242.75 10 7 S 2372.75 19,21,23,25 3100 A 727.25| 2020.0 2N 352.75 13 8 S 2392.75 27,29,31,33 3100 A 707.25| 2020.0 2N 372.75 14 VLBA | ONSALA60, WETTZELL Chan Sky Tracks LO IF BBC | LO IF BBC BBC# 1 X 8365.75 2, 4, 6, 8 7600 B 765.75| 8080.0 A1 285.75 3 2 X 8445.75 10,12,14,16 7600 B 845.75| 8080.0 A1 365.75 4 3 X 8805.75 18,20,22,24 9600 D 794.25| 8080.0 B1 725.75 5 4 X 8925.75 26,28,30,32 9600 D 674.25| 8080.0 B1 845.75 6 5 S 2232.75 3, 5, 7, 9 3100 A 867.25| 2020.0 C1 212.75 9 6 S 2262.75 11,13,15,17 3100 A 837.25| 2020.0 C1 242.75 10 7 S 2372.75 19,21,23,25 3100 A 727.25| 2020.0 D1 352.75 13 8 S 2392.75 27,29,31,33 3100 A 707.25| 2020.0 D1 372.75 14 Special operations for non-VLBA stations: ========================================= All non-VLBA stations: Please note that due to the frequency sequence, phase-cal will not be visible with a 10 kHz viewing filter in the USB channels. If you have another means to verify phase-cal, please use it. If you have a Mark IV Decoder, please contact Ed.Himwich@nasa.gov if you would like advice on how to set it up to check phase-cal for this frequency sequence. HARTRAO: This station uses a DBBC rack. Please use the procedures generated by DRUDG. BBCs 3 & 4 are used at X-band with IF A, input 1. BBCs 5 & 6 are used at X-band with IF B, input 2. BBCs 9, 10, 13 & 14 are used for S-band with IF C, input 1. NYALES20 and WETTZELL: These stations have Mark IV or Mark 5 racks. Please use the procedures generated by DRUDG. VCs 3 & 4 are used at X-band with IF 1. VCs 5 & 6 are used at X-band with IF 3. VCs 9, 10, 13 & 14 are used at S-band with IF 2. ONSALA60: This station uses a DBBC rack. Please use the procedures generated by DRUDG. BBCs 3 & 4 are used at X-band with IF A, input 1. BBCs 5 & 6 are used at X-band with IF B, input 1. BBCs 9 & 10 are used for S-band with IF C, input 1. BBCs 13 & 14 are used at S-band with IF D, input 1. The IF3 command in the procedure IFDSX assumes that VC3 and VC10 will be patched to High. Please verify that the switches for your IF3 module are wired this way, and if they are not please edit the IF3 command to change the switches. The standard wiring is described in "help=if3". If you have questions about the wiring, please contact Brian Corey at Haystack. If you wish to record back-up channels, please add appropriate valo=..., va=... vblo=... and vb=... commands in the VCSX8 procedure. CHECKLIST for non-VLBA stations =============================== Please follow the checklist below to ensure you have done all the necessary steps for this session: 1. Make .prc file with DRUDG and check them out, or use the procedures from the last RV session. Check out parity check procedures. 2. Make the .snp file with DRUDG. 3. Set up your system to monitor the clocks with the "gps-fmout" or "fmout-gps" commands. If you have questions about this, please contact Ed Himwich as soon as possible. 4. Send a "ready" message an hour or so before the session to the ivs-ops mail list (ivs-ops@lists.nasa.gov). Copy analysts@nrao.edu on your ready message. 5. Send a "start" message soon after you have started recording. Copy analysts@nrao.edu on the message. 6. At the end of the session, send a "finish" message summarizing how the session was conducted. Copy analysts@nrao.edu on your message. 7. Transfer your log file to your normal IVS data center. The directories for the IVS servers are listed below: ftp ivsopar.obspm.fr/ivsincoming ftp ivs.bkg.bund.de/ivsincoming Correlation =========== This session will be correlated at the NRAO/VLBA on the VLBA DiFX software correlator. Most of the Mark4 stations are now E-transfering their data to Haystack, where it will be copied and shipped to the VLBA in Socorro, New Mexico. These stations will need to coordinate this with Haystack Observatory (contact: Jason SooHoo at jsoohoo@haystack.mit.edu). The VLBA needs to process the session at their correlator as soon as possible because of limited media. So please try to set up the E-transfer as soon as possible after the session ends. If you need to ship the media instead, please ship it to Socorro as soon after the session as is practical. It should be shipped to the following address: Socorro address for media shipping: VLBA Array Operations Center National Radio Astronomy Observatory Attn: Juan Cordova 1003 Lopezville Road Socorro, NM 87801 U.S.A. Phone: 575-835-7000 Shipping and VLBA contact information is also given at: https://science.nrao.edu/facilities/vlba/contact/shipping_information. Please use one of the recommended shipping companies (FedEx, UPS, DHL, TNT). Please ship your media to the VLBA the same day the session ends or the next business day (just like the R1/R4 media is shipped). If you know that there is going to be a problem sending your media to the VLBA the same day the session ends or the next business day, please let us (David.Gordon-1@nasa.gov) know as soon as possible so that we, along with the VLBA, can determine the best course of action. If you have any questions or comments, please let us know.